KH 1500 PATIO-HEATER - Heating PARKSIDE - Free user manual and instructions

Brand	PARKSIDE
Model	KH 1500 PATIO-HEATER
Product type	Radiant heater
Power	1500 W
Rated voltage	230 V ~ 50 Hz
Number of power levels	3 (0, 1 bar, 2 bars)
Heating element type	Heating rods (quartz)
Anti-tip safety	Safety switch on the bottom
Safety distance	Minimum 50 cm around the device
Body material	Steel
Color	Black (estimated)
Weight	Approximately 2.5 kg
Dimensions (height)	Approximately 65 cm
Dimensions (base diameter)	Approximately 28 cm
Cable length	Approximately 1.5 m
Use	Indoor and protected outdoor (balcony, terrace sheltered from rain)
Cleaning	Damp cloth, soft brush for heating rods
Assembly	Simple: two-part base, screw nut fastening
Adjustable heating element	Tilts vertically for storage
Included accessories	Manual, fixing nut

Frequently Asked Questions - KH 1500 PATIO-HEATER PARKSIDE

How to turn on the device?

Make sure the device is on a flat surface and the heating element is in a horizontal position. Plug the power cord into a 230 V outlet. Turn the power selector (4) to position 1 (one bar) or 2 (two bars).

What to do if the device does not turn on?

Check that the power cord is properly connected, that the socket fuse works (try another device) and that the device is on a flat surface to activate the safety switch (8).

Can the device be used outdoors?

Yes, but only in a dry place sheltered from humidity (covered balcony, protected terrace). Do not use it in the rain or near a swimming pool.

What minimum distance should I keep around the device?

Keep a distance of at least 50 cm between the device and any flammable object (curtains, furniture, etc.).

How to clean the device?

Turn off the device, unplug it and let it cool down. Clean the exterior with a damp cloth (no abrasive products). The heating rods can be brushed with a soft long-handled brush.

How to assemble the stand?

Place the heating element (3) with the bars facing down. Insert the lower part of the stand into one half of the base (the one with a peg). Add the other half and press to snap together. Screw the provided nut into the hole.

Does the device consume a lot of electricity?

With a power of 1500 W, it consumes 1.5 kWh per hour of operation at full power. The cost depends on your electricity rate.

Can I leave the device on all night?

No, it is not recommended to leave the device unattended. Use it only when you are present and turn it off after use. Never cover the device.

What to do in case of malfunction?

Unplug the device immediately. Check if the problem comes from the cable or fuse. If the problem persists, contact a qualified professional. Do not attempt to repair it yourself.

How to store the device after use?

Turn off and unplug the device. Let it cool down. Rotate the heating element to a vertical position to save space. Store it in a dry place, out of reach of children.

USER MANUAL KH 1500 PATIO-HEATER PARKSIDE

The floor heater at a glance. 8
Safety instructions. 8
Getting started. 9
Assembling the appliance. 9
Operation 10
Running the heater. 10
After use. 10
Cleaning. 10
What if ... 10
Technical data. 10

DEAR CUSTOMER!

Your new floor heater is easy to use and with its 1.500 W output quickly creates a good heat. It is portable and due to its moveable heating element is easy to store.

The floor heater is equipped with a safety switch on the underside of the appliance. Should the heater fall over, the power supply is immediately cut off and the appliance switches itself off.

THE FLOOR HEATER AT A GLANCE

Components

(1) Base stand
(2) Power cable and plug
(3) Heating element
(4) Output regulator
(5) Handle
(6) Safety holder
(7) Heating rods
(8) Safety switch (on the underside of the stand)

SAFETY INSTRUCTIONS

Please, for your own safety, carefully read these safety instructions before starting up.

LOOK OUT FOR CHILDREN!

An electrical appliance is not a toy. Children do not recognise the dangers that could arise through use of electrical appliances. Make your children aware of the dangers, which could be associated with this appliance:

• Burns from touching the appliance or hot air.
• Dangers from electrical current.
• Fire if the appliance is covered.

For these reasons, the appliance should always be supervised and kept out of reach of children. Children must not use the appliance. In a household with children, always switch the appliance off after use and unplug in from the mains.

• The appliance must not be used if it is in any way damaged. Regularly check the heating rods and power cable. The isolation must not be damaged or crushed.
• Only use the appliance in it's fully assembled state, upright and with the heating element in a horizontal position. Otherwise the housing could overheat, which could lead to a fire risk.
• Stand the floor heater on a level surface. Leave enough space on all sides and above.
• The floor heater can only be used if it is placed on a level surface. On an uneven surface, the safety switch on the underside of the appliance will not be pushed in and the floor heater will not be able to be used. For safety reasons, this switch must not be bypassed or otherwise put out of action. Keep the safety switch clean to provide trouble free use.
• The device must only be used in dry surroundings and away from flammable materials, liquids or gasses. The floor heater is intended for indoor use only. If used on a patio or balcony, the appliance absolutely must be supervised and protected from moisture. This floor heater must not be used in the immediate vicinity of a bath, shower or swimming pool.
• Position the power cable so that there is no risk of tripping. The cable must not be damaged by sharp edges or heat. Use only approved extension cables.
• The appliance must be switched off when it is to be plugged into the mains.

• The appliance may only be connected to an earthed mains socket with 220/230 Volts. Your household electricity supply must correspond with the voltage shown on the type plate. Non-earthed plug sockets for razors are not suitable.

• Do not stand the appliance directly under a lug socket.

• Never use the appliance with timer automatic switches e.g. timer switches, which automatically switch the appliance on as accidental covering of the appliance could lead to a fire risk.
• The appliance may only be connected to an extension cable, which is suitable for an output of 1.500 Watts.
• Do not cover the appliance and do not place anything over or on top of the appliance. Keep a distance of at least 50~cm to all flammable objects. There is a fire risk!
• Do not touch the front side of the heating element, the metal casing or the two handles on the front side during and shortly after use. These parts become very hot. Danger of being burnt!
• Never clean the appliance with easily flammable cleaning agents as for example Petrol or Spirit.
• When connected to the mains, only move the appliance using the handle on the backside of the heating element. Only move the appliance when it is switched off and has cooled.
• Do not allow hair or clothing to get too near the appliance when in use.
• Never submerge the appliance, the power cable or the plug in water.
• If a problem occurs while in use or while cleaning, first unplug the appliance. Allow the appliance to cool before cleaning.
• Unplug the appliance when not in use.
• When unplugging the appliance, always pull by the plug not the cable.
• Repairs must be carried out by qualified experts only to avoid danger or accident. This also applies to the changing of the mains power cable. In the case of unqualified repair being carried out, the guarantee becomes void.
• The floor heater is intended for domestic use only, not for commercial use.
• If the appliance is passed on to someone else, include these instructions for use. Only in this way can the next person use the appliance safely.

GETTING STARTED

Assembling the appliance

• Lay the heating element (3) with the stand carefully on the floor, with the heating rods facing downwards.
• Lay the bottom end of the stand into the half of the base, which has a pin on the inside. The pin should thereby be stuck into the upper hole of the stand.
• Lay the second half of the base stand on the first half and press until the two halves click together.
• Stick the provided nut on the one side into the hole in the base and screw everything together with the bolt.
• Turn the heating element up to the label in a horizontal position.

Now your floor heater is ready for use.

OPERATION

Running the heater

• Position the floor heater in a dry place. There must be at least 50~cm free on all sides and above. The floor must be level, so that the safety switch on the underside is pressed in. There must be no objects such as furniture or curtains between the floor heater and the person or things to be warmed.

• Turn the heating element (3) up to the label in a horizontal position.

• Make sure that the output regulator (4) is switched to "0" and plug the plug (2) into a plug socket. Warning! The voltage must correspond with the notice on the type plate on the output regulator (4)!

• Switch the output regulator (4) to the desired setting:

0 = 0ff

1 = One heating rod switched on

2 = Both heating rods switched on

While in operation, only touch the appliance by handle (5).

Attention!

The appliance may only be moved when it is switched off and not connected to the mains.

AFTER USE

• Switch the appliance off with the output regulator (4), when the desired room temperature is reached.
• If the appliance is no longer needed, disconnect from the mains and let it cool down.
• To save space when storing the appliance, turn the heating element (3) back to a vertical position.

CLEANING

• Do not use abrasive cleaning agents as they could damage the surface of the appliance.
• Never clean the appliance with easily flammable cleaning agents such as petrol or spirit.
• Before cleaning, switch the appliance off, unplug it from the mains and allow it to cool down.
• Clean the appliance with a lightly moistened cloth.
• The heating rods are best cleaned with a brush with long soft bristles.
• Never submerge the appliance in water or other liquid.

WHAT IF...?

Cannot be switched on.

• check if the plug is correctly plugged in.
• check if the plug socket is in working order (e.g. with a lamp).
• Is the floor heater standing on a level surface, so that the safety switch (8) on the underside is pressed in?

TECHNICAL DATA

Nominal voltage: 230V 50Hz

Nominal output: 1.500 W

In the course of product improvement, we reserve the right to technically and optically alter the product.

CONTENU

WAT GBEURT ER WANNEER...?